How to Cover a Step with Wood: A DIY Guide 2026

Paulo Vivere
How to Cover a Step with Wood: A DIY Guide
This page may contain affiliate links.

Are you looking to give your home a cohesive, polished look by blending a concrete or brick step with your existing parquet flooring? In this guide, we’ll show you exactly how to cover a step using laminate and plywood. This project is perfect for that small step leading from your living room to the garden. It requires precision, but it is well within the reach of a good DIY enthusiast.


DIY project photo
Maybe you’ve decided to rip up the old carpet or tiles and replace them with wood. If your room has a door leading to the garden with a small step to overcome, covering it to complete the job doesn’t require a huge amount of effort. Once you have gathered your materials, the whole task can be completed in less than an hour. To get started on the right foot, ensure you have all the necessary home improvement tools and supplies on hand.


Furniture with Meaning.

Find Original Home Decor sparking conversation at Grand Goldman Shop.


Preparing the Step Structure

The tread of the step needs a solid, flat base. If the top of the old step has bumps that you cannot remove, it is better to let the new tread rest directly on the riser and the sides. For the vertical elements, choose boards that exceed the existing level by 1-2 mm.

ADVERTISEMENT

For the tread, cut a piece that protrudes slightly over the sides and the riser. This also benefits the aesthetic appearance of the step. The real challenge lies in using invisible fastening systems. For the vertical parts, it is best to fix a first layer of 15 mm thick plywood, anchoring it with expanding wall plugs, and then cover everything with thin veneered planks applied with simple glue.

The planks need to be cut to size. To hide the edges, you can either join them with a 45° cut or conceal everything behind an angle bracket. For the tread, it is less convenient to use the same system as the riser and sides, as veneer is more delicate than solid wood. To hide the heads of the screws, you drill a wider superficial hole to close with a wooden plug. These materials and products are readily available at hardware stores. Consider upgrading your workspace with a sturdy work surface or desk for your future projects.

Structure and Concealment

The laminate tread rests on the plywood riser and sides, which are screwed in with expanding wall plugs. To mask the heads of the fixing screws on the tread, use Ø 15 mm wooden plugs, choosing ones with a grain similar to the surrounding wood.

For the front and side covering of the step, thin veneered planks are sufficient. These are fixed with contact glue or silicone. A clear finish not only looks great but also protects the step, giving it greater durability. To keep your new step looking pristine, a soft rug at the base can help trap dirt and moisture.

ADVERTISEMENT

Choosing Your Materials

  • Laminate Tread: This provides the walking surface. It should be durable and match your floor. You can find excellent options in our home improvement collection.
  • Plywood Base: Used for the riser and sides to create a stable structure.
  • Veneered Planks: Perfect for the vertical sections to give a uniform wood look.
  • Wooden Plugs: Essential for hiding screw heads for a professional finish.

Tools You Will Need

  • Saw (hand saw or circular saw)
  • Drill and drill bits
  • Screwdriver
  • Measuring tape and square
  • Clamps
  • Sandpaper
  • Glue (contact adhesive or silicone)

Step-by-Step Instructions

1. Measure and Cut the Plywood

Measure the height and width of the riser and the sides of the step. Cut your 15 mm plywood to these dimensions. This will serve as the solid base for your veneer. Proper lighting is crucial for precise cuts, so check out our lighting options to brighten your workshop.

2. Fix the Plywood Base


DIY project photo
Drill holes through the plywood and into the concrete or brick step. Insert expanding wall plugs and screw the plywood firmly into place. Ensure it is level and secure.

3. Apply the Veneer to the Vertical Parts

Cut the thin veneered planks to size. Apply contact glue or silicone to the back of the planks and press them firmly onto the plywood base. For a clean look, join the planks at a 45° angle at the corners.

4. Prepare and Install the Tread

Cut the laminate tread so it overhangs the riser and sides slightly (about 1-2 cm). Drill counter-sunk holes from the top of the tread down into the plywood base. Screw the tread in place.

ADVERTISEMENT

5. Conceal the Screws

Apply glue to the wooden plugs and tap them into the counter-sunk holes. Once the glue is dry, sand the plugs flush with the surface of the tread. This creates an invisible fixing point.

6. Apply the Finish

Sand the entire step lightly. Apply a clear varnish or wood oil to protect the wood and enhance its natural beauty. This step is essential for durability, especially in high-traffic areas. Adding a curtain or blind nearby can protect the step from direct sunlight, preventing fading over time.

FAQ

Can I use this method for outdoor steps?

This method is best for covered or indoor steps. For fully exposed outdoor steps, you would need exterior-grade laminate and waterproof adhesives. You might also consider a garden supply solution like stone or specialized outdoor tiles for better weather resistance.

What if my step is an irregular size?

You can easily cut the plywood and laminate to fit any irregular size. Just be sure to measure carefully and use a template if necessary. A shelving unit or bookcase can be a great place to store your measuring tools and templates for future projects.

ADVERTISEMENT

How do I match the new step to my existing floor?

Take a sample of your existing flooring to the store to find a laminate or veneer that matches in color and grain. Many manufacturers produce coordinating stair nosing and treads.

Is it necessary to use plywood as a base?

Yes, using a 15 mm plywood base ensures a perfectly flat and stable surface for the laminate tread and veneer. It also provides a strong anchor for the screws, which is much better than fixing directly into old concrete or brick.

Can I paint the step instead of using wood?

Absolutely! If you prefer a painted look, you can follow the same structure but use MDF or plywood for the final surface and paint it. However, wood provides a warmer, more classic look that complements parquet flooring beautifully. To complete the look of the room, consider coordinating your new step with a sofa or dining table that features similar wood tones.



Browse Grand Goldman Home Decor

Discover unique craftsmanship home decor and furniture at the Grand Goldman Shop.

ADVERTISEMENT
Grand Goldman home decor best outdoor cooking for entertaining guests | affordable outdoor cooking for patio relaxation | premium outdoor cooking for al fresco dining | best bbq grills outdoor cooking supplies for entertaining guests | affordable bbq grills outdoor cooking supplies for patio relaxation | premium bbq grills outdoor cooking supplies for al fresco dining | best coolers decor for every home | stylish coolers accessories online | affordable coolers for any room | best garden supplies for raised bed vegetable garden | affordable garden supplies for small backyard patio | premium garden supplies for front yard landscaping | espresso wall mounted coat rack | wooden entryway storage shelf | 4 dual hook entry organizer | 3 in 1 entryway hall tree | storage bench with coat hooks | black shoe storage organizer | grey power reclining sofa set | 3 piece leather recliner couch | modern sectional reclining sofa | modern executive computer desk | wooden storage cabinet desk | large office desk with doors |

ADVERTISEMENT
Paulo Vivere

Author

Paulo Vivere

Paulo Vivere is a pest control specialist and Grand Goldman writer, sharing practical, research-backed guidance on pest prevention, identification, and safe home solutions.


SPONSORED

Get Lifetime Access to the Lastest Movies, with Exclusive Offers & Free Express Order Delivery.

ADVERTISEMENT